1081) 9/29/2007 Q223025 HOWTO: Call GetNetworkParams/GetAdaptersInfo From Visual Basic (Q223025)
This article illustrates how to programmatically retrieve IP configuration information similar to the IPCONFIG.EXE utility. It demonstrates how to use the IP Helper APIs GetNetworkParams() and GetAdaptersInfo() from Visual Basic. The libraries 1082) 9/29/2007 Q250204 The /INSERT Option for Doskey Is Turned On by Default (Q250204)
Doskey is a command-line utility for recalling MS-DOS commands, editing command lines, and creating macros. In Windows Millennium Edition (Me), Doskey is loaded by default when you start a command session (or window). Windows Me loads Doskey with the 1083) 9/27/2007 Q250205 UDMA Is Not Enabled After You Upgrade to Windows ME (Q250205)
After you upgrade to Windows Millennium Edition (Me), your hard disk may not be configured to use Ultra Direct Memory Access (UDMA). Note that this issue may occur even if your hard disk and hard disk controller support UDMA. 1084) 9/26/2007 Q250206 Problems Printing When You Use a Canon BJC-4200 Printer with a Photo Ink Cartridge (Q250206)
When you print an image by using a Canon BJC-4200 printer with the 22e photo ink cartridge, the printed output may appear compressed on the page. 1085) 9/23/2007 Q250210 Unable to Connect to an Internet User by Using VDOPhone with Internet Connection Sharing (Q250210)
When you try to use the VDOnet VDOPhone program to connect to an Internet Connection Sharing (ICS) client computer that is also running VDOPhone, you may be unable to establish a connection. 1086) 9/30/2007 Q250214 Windows Millennium Setup Stops Responding at 100 Percent During the Install Wizard (Q250214)
When you install Windows Millennium Edition (Windows Me), Setup may stop responding during the Preparing Install Wizard process. When the progress indicator reaches 100 percent, Setup pauses for an extended period of time, and then proceeds with the 1087) 9/23/2007 Q250231 System Restore Points May Not Be Created for Hardware Device Driver Installations (Q250231)
After installing hardware device drivers or supplemental utilities for hardware devices, you do not see System Restore Points created in the System Restore utility. 1088) 9/28/2007 Q250232 'Code 7' Error Message Is Displayed in Device Manager on Computer Using an R2 PC Card (Q250232)
When you use a Dell Latitude CPi Notebook portable computer with an R2 (16-bit) PC Card, "Code 7" may be displayed in Device Manager, next to the PC Card device. 1089) 9/28/2007 Q250238 Setver.exe Is Not Loadable in Windows Millennium Edition (Q250238)
If you run Setver.exe at a command prompt in Windows Millennium Edition (Me), you receive the following error message: NOTE: Setver device not loaded. To activate Setver version reporting you must load the Setver.exe device in your Config.sys. 1090) 9/28/2007 Q250239 Hardware Profile Not Detected After Resuming from Hibernation Mode (Q250239)
If you use hardware profiles and you upgrade to Windows Millennium, your laptop computer may not change hardware profiles when it resumes from hibernation mode. Or your laptop may stop responding (hang) when you try to use it. 1091) 9/30/2007 Q250240 "Open in New Window" Feature in PCHealth's Help Center Disabled (Q250240)
When you attempt to use the Open in New Window feature in the Help Center of PCHealth, you receive no response and a new window is not opened. 1092) 9/30/2007 Q250255 Device Manager Does Not List the Serial Mouse (Q250255)
After Microsoft Windows Millennium Edition setup is completed, or after you remove your serial mouse and restart the computer, the mouse is not listed as being installed, although it works correctly. When you open System Properties in Control 1093) 9/30/2007 Q250256 Floppy Disk Controller Denies Hibernation or Standby (Q250256)
When your computer has been idle for an amount of time that is sufficient for it to enter Standby mode, or if you try to use Standby mode, your computer does not enter Standby mode, or returns from Standby mode immediately. You may also receive the 1094) 9/30/2007 Q250259 Adaptec SCSI Controller in ACPI Mode Causes Standby to Fail (Q250259)
When you use Windows Millennium Edition (Me), and your computer enters Standby mode, it suddenly exits Standby and restores your desktop. 1095) 9/30/2007 Q250323 Mandatory User Profiles Do Not Work on Local Computer (Q250323)
Although you can use local user profiles on a Windows 95-based, Windows 98-based or Windows Me-based computer, you cannot make the profiles mandatory. Attempting to rename a User.dat file to User.man in a local profile folder does not work properly.
1
2
.... .... 69
70
71
72
[ 73 ]
74
75
76
77
.... .... 90
91
Previous Page
Page 73 of 91
Next Page
|